當遇到振動盤振動慢、沒力、送料速度不如以前、出料斷斷續續時，先檢查振動盤的臺面是否水平，不水平的話，將臺面放平即可。另外要檢查臺面是否有缺陷或是缺少硬度。如果懸吊于設備臺面，會造成振動過弱，臺面厚度應該至少達到1- 1/2"，這樣才不會吸振。除了臺面外，還要檢查盤內是否有雜物，雜物會影響機械的正常運行。之后就是彈簧片斷裂或者彈簧片的彈性失效，底板過薄或者地板斷裂。圓柱式撐腳必須配備三角支撐片，線圈氣隙應盡可能小，如果過度會有意外的問題。機器節奏過快導致零件從振盤滑落，電網波動，還是電壓不穩定的問題，控制器需要重新調整頻率和電壓以適應電網波動，超差、彎曲、含油軸承等零件問題也是會遇到的。盤與底座緊固螺絲不緊或位置不對，零件過多容易引起卡料的問題，底盤調整不當，盡量不要去動底盤，物料變更，應當重新修整盤面并重調底盤， 在使用氣吹的場合可能會產生一些問題，可能存在：氣壓不穩、氣源污染、含水或油，這些污染。