1、注意五金塑料件振動盤電壓大小要求：

國家標準規定，并聯電容器工頻長時刻過電壓值zui多不超越1.1倍額定電壓。關于大中型異步變頻振動盤考慮到確保必定的補償效果，而又會出現較高過電壓，這時可選用壓敏(min)器件限制過電壓。

2、注意振動盤維持電壓時刻要求：

關于需主動投切的變頻振動盤，或可逆運轉的變頻振動盤，從正轉狀態到反轉狀態的過渡時刻內，電容器的端電壓必須降到額定峰值(初始值)電壓的10%以下，不然由于自勵磁的添加，變頻振動盤的端電壓將升高到不能允許的程度。當選用主動投切時，投、切時刻間隔的時限應大于或等于電容器放電時刻。

3、注意振動盤避免發作自勵磁和諧振：

為避免被補償變頻振動盤發作自勵磁的情況發作，就地補償的電容器容量選用應盡量不過補。由于變頻振動盤堵截電源后，其轉速不能當即降為零，電容器對變頻振動盤繞組放電，使變頻電機得到勵磁，有可能造成短時過電壓。